Home

Beams, Slurs and Ties


Beams

The default beam in the library is simply a rectangle 100px by 15px. Since they will usually need to be transformed for angle and scale, they have additional attributes;

     
      <use xlink:href="#be"
       transform="translate(x,y) skewY(n°) scale(1,1)">
     
    

The 'translate' gives the beam it's own 0,0 within the measure, so that the transforms are centered on the upper-left hand corner of the beam; not of the measure. The 'skewY' is the angle in degrees the beam will be; default is clockwise, a hyphen(minus) '-' is counter clockwise. The 'scale' is the length it will be. The number 100 is probably the most convenient number for a default value: if the length it needs to reach is 257px, then you scale(2.57,1); or 89px: scale(.89,1).


music engraving

On a standard stem* (up), the beam is placed +14x,-85y of the note coordinates. The code for the image above is:

     
      <use x="50" y="48" xlink:href="#solnu"/><!-- note -->
       <!-- beam -->
      <use xlink:href="#be"
       transform="translate(64,-37) skewY(0) scale(1.25,1)"/>
      <use x="175" y="48" xlink:href="#solnu"/><!-- note -->
     
    

* The library contains notes with long and short stems.


To calculate the angle [skewY()] of a beam, divide the interval of the notes by the distance between them: 12 ÷ 114 = .105, which is the tangent of the angle. With a scientific calculator, invert the tan to degrees: 6.01°.

music engraving

     
      <use x="50" y="48" xlink:href="#solnu"/>
      <use xlink:href="#be"
       transform="transform="translate(64,-37) skewY(-6.01) scale(1.14,1.01)"/>
      <use x="164" y="36" xlink:href="#solnu"/>
     
    

Notice that the scale 'y' has increased also. A very small amount for this angle, but important to know why.

As the angle increases the beam becomes narrower. The beam on the left (below) has no 'y' scaling. The beam on the right has been compensated. To calculate the proportion of scale for 'y':
15 ÷ cos(angle°) ÷ 15, or:
15 ÷ [cos(6.01°)=15.08] ÷ 15 = 1.01; for the upper example, and
15 ÷ [cos(35.75°)=18.48] ÷ 15 = 1.23; for this example.

music engraving

     
      <use x="200" y="84" xlink:href="#solnu"/>
      <use xlink:href="#be"
       transform="translate(214,-1) skewY(-35.75) scale(1,1.23)"/>
      <use x="300" y="12" xlink:href="#solnu"/>
     
    

Most of the time a skewY() and a scale(,) are all you need for beams (8th, 16th, 32nd). The exceptions are a dotted eighth note followed by a sixteenth note, or a double dotted eighth note followed by a thirty second, etc., and the reverse of these; but only for notes with stem down. This is because beams with partial beams need to be flipped. There is no flip() transform in SVG, but there is transform="matrix(1,0,0,1,0,0)".

It would be more comfortable to take the blue pill, but the red pill will show you how far down the rabbit hole goes.

A matrix can execute all of the transforms together:
scale, translate, skewX, skewY, rotate
or whichever ones you need.

Notice that with matrix you use tangent rather than angle for skews. In addition, you must multiply the tangent of skewY by the scale of 'x' to get the correct angle. I have yet to learn how to use 'rotate' in combination with the other properties, but you can still use rotate() and matrix(). Always rotate first!
Also, you must add 15px,y to the position of a flipped beam (the width of a beam).

music engraving

Here it is at work:

     
      <use x="50" y="24" xlink:href="#solnd"/>
      <use x="50" y="33" xlink:href="#dot"/>
      <use xlink:href="#be.1r"
       transform="matrix(1.5,.24,0,-1.01,36,109)"/>
      <use x="200" y="48" xlink:href="#solnd"/>
     
    

Slurs and Ties

Unlike beams, slurs are rotated for angle. As with beams, the default slur/tie is 100px long, and horizontal. It's x,y 0,0 is the left point. The instructions for flipping a beam are the same for slur/tie's.


Placement of slurs/ties is partly a matter of taste. I've seen some sheet music where they touch the notes, and I don't like the look of that. Below is x+24px, y-18px, and a scale of x1.14; 12px before the next notes center (150-24-12=114). This works well for note to note, stem up, but different arrangements need different placement.

music engraving

     
      <use x="50" y="72" xlink:href="#solnu"/>
      <use xlink:href="#slr"
       transform="translate(74,54) rotate(0) scale(1.14,1)"/>
      <use x="200" y="72" xlink:href="#solnu"/>
     
    

A slur from stem to stem is the easiest to place. From note to note it will need to be shortened at both ends.

music engraving

     
      <use x="50" y="36" xlink:href="#solnu"/>
      <use xlink:href="#be"
       transform="translate(64,-49) skewY(16.07) scale(1.25,1.04)"/>
      <use xlink:href="#slr"
       transform="translate(68,-56)rotate(16.07) scale(1.28,1)"/>
      <use x="175" y="72" xlink:href="#solnu"/>
     
    

Next